Methodology for the design » History » Version 1

GAY, Adrien, 03/23/2015 09:58 AM

1 1 GAY, Adrien
h1. Methodology for the design
2 1 GAY, Adrien
3 1 GAY, Adrien
In order to fulfil the requirements, we have developed a methodology in three steps:
4 1 GAY, Adrien
5 1 GAY, Adrien
•	Evaluation of the required Modulation and Coding (MOCOD)
6 1 GAY, Adrien
•	Estimation of the required Eb/N0 for this MODCOD
7 1 GAY, Adrien
•	Computation of the (G/T) of the ISAE receiver required to cope with this Eb/N0
8 1 GAY, Adrien
9 1 GAY, Adrien
Then, from the (G/T) value, we can discuss about the type of antenna that can be used for the ISAE receiver according to the constraints developed in part II.1)
10 1 GAY, Adrien
11 1 GAY, Adrien
12 1 GAY, Adrien
1)	Modulation and Coding:
13 1 GAY, Adrien
14 1 GAY, Adrien
As developed in II.2.a, we have the following relation between the modulation, the coding and the roll-off:
15 1 GAY, Adrien
16 1 GAY, Adrien
formula
17 1 GAY, Adrien
18 1 GAY, Adrien
For the sake of simplicity, we will fix the roll off to alpha=0.2, which is a typical value enabling a good tradeoff between the spectral efficiency and the threshold detector performances (used in DVB-S2 for example).
19 1 GAY, Adrien
20 1 GAY, Adrien
Then, considering that M is a power of 2 and rho<1, we can estimate from the previous relation the minimal MODCOD required:
21 1 GAY, Adrien
22 1 GAY, Adrien
Conclusion: 
23 1 GAY, Adrien
24 1 GAY, Adrien
After fixing the value of the roll-off (here alpha=0.2), the MODCOD is directly conditioned by the values of B and Rb.
25 1 GAY, Adrien
26 1 GAY, Adrien
27 1 GAY, Adrien
28 1 GAY, Adrien
2)	Required Eb/N0:
29 1 GAY, Adrien
30 1 GAY, Adrien
  We choose the coding technique based on LDPC codes as introduced in DVB-S2 standard. This is a powerful coding scheme allowing higher spectral efficiencies for a given Eb/N0 compare to basic modulations.
31 1 GAY, Adrien
32 1 GAY, Adrien
Here is a table extracted from DVB-S2 standard (ETSI EN 302 307 V1.2.1, table 13):
33 1 GAY, Adrien
34 1 GAY, Adrien
35 1 GAY, Adrien
36 1 GAY, Adrien
(table)
37 1 GAY, Adrien
38 1 GAY, Adrien
39 1 GAY, Adrien
Given the MODCOD previously determined, we can read in this table the required value of Es/N0. Then, Eb/N0 can be computed thanks to the relation:
40 1 GAY, Adrien
41 1 GAY, Adrien
Eb/N0=
42 1 GAY, Adrien
43 1 GAY, Adrien
With T the value of the spectral efficiency corresponding to the given MODCOD (second row of the table above). In fact, this value of spectral efficiency does not take into account the roll-off of the shaping filter, so we correct it in order to get the real spectral efficiency of the system.
44 1 GAY, Adrien
45 1 GAY, Adrien
46 1 GAY, Adrien
Remarks:
47 1 GAY, Adrien
48 1 GAY, Adrien
•	The table specifies the ideal Es/N0. Margin for non-ideal demodulator will be taken into account in the computation of the link budget.
49 1 GAY, Adrien
•	We can notice that lower MODCODs sometimes require higher Eb/N0 (at transition between modulations). In fact, lower modulation are preferred if possible even if it requires higher Eb/N0. In fact, there are more robust to perturbations such as multipath or phase noise for instance. This has to be kept in mind in order to explain some curves plotted in the result part.
50 1 GAY, Adrien
51 1 GAY, Adrien
52 1 GAY, Adrien
53 1 GAY, Adrien
3)	Computation of (G/T):
54 1 GAY, Adrien
55 1 GAY, Adrien
From the expression of the link budget (cf part II.2.b), we get:
56 1 GAY, Adrien
57 1 GAY, Adrien
(G/T)=
58 1 GAY, Adrien
59 1 GAY, Adrien
With Lmarg the only unknown which has to be evaluated in order to compute (G/T).
60 1 GAY, Adrien
61 1 GAY, Adrien
An accurate evaluation of the margin can be tricky and is not the aim of this project. Then we just roughly evaluated it:
62 1 GAY, Adrien
•	Depointing of the antennas: Ldep= 3dB + 3dB=6 dB
63 1 GAY, Adrien
•	Non-ideal demodulator: Ldem= 3 dB
64 1 GAY, Adrien
•	Atmosphere attenuation (clear sky conditions): Lprop= 1.5 dB
65 1 GAY, Adrien
•	Interferences: Lint= 1.5 dB
66 1 GAY, Adrien
67 1 GAY, Adrien
Then, we took Lmarg= 12 dB. However, the value of the margin can easily be modified in the simulations presented in part IV if needed.