FlexACM » History » Version 3
GAY, Adrien, 12/15/2014 06:13 PM
1 | 1 | Cuadro, Juan Pablo | h1. FlexACM |
---|---|---|---|
2 | 1 | Cuadro, Juan Pablo | |
3 | 1 | Cuadro, Juan Pablo | |
4 | 1 | Cuadro, Juan Pablo | FlexACM In-band signalling on the forward link: |
5 | 2 | Cuadro, Juan Pablo | !{width: 45%}InbandSigFW.png(FlexACM In-band signalling on the forward link.)! |
6 | 1 | Cuadro, Juan Pablo | |
7 | 1 | Cuadro, Juan Pablo | FlexACM In-band signalling on the return link: |
8 | 2 | Cuadro, Juan Pablo | !{width: 45%}InbandSigRT.png(FlexACM In-band signalling on the return link.)! |
9 | 3 | GAY, Adrien | |
10 | 3 | GAY, Adrien | |
11 | 3 | GAY, Adrien | |
12 | 3 | GAY, Adrien | |
13 | 3 | GAY, Adrien | As seen previously, the demodulator selects the optimal MODCOD based on the estimation of the signal Es/N0. However, the choice of the MODCOD is not only based on the comparison of the Es/N0 with the theoretical thresholds as distortion of the signal has to be taken into account (distortions from the channel or causes by a saturated transponder for examples). Moreover, we add some margin in the link budget by safety. |
14 | 3 | GAY, Adrien | |
15 | 3 | GAY, Adrien | Then, the MODCOD is chosen by comparison of the estimated Es/N0 with the theoretical threshold of the MODCOD + the distortion + the margin, as shown on the figure below |
16 | 3 | GAY, Adrien | |
17 | 3 | GAY, Adrien | (figure p 124 newtec user manual). |
18 | 3 | GAY, Adrien | |
19 | 3 | GAY, Adrien | |
20 | 3 | GAY, Adrien | |
21 | 3 | GAY, Adrien | We can notice on this figure that margin for selecting a higher MODCOD is higher that margin for selecting a lower MODCOD. This is advised by the constructor to create hysteresis and avoid togglings of MODCODS for specific values of Es/N0. |
22 | 3 | GAY, Adrien | |
23 | 3 | GAY, Adrien | The distortion is estimated thanks to a NoDE (Noise and Distorsion estimator) feature implemented in the modem, margins can be set up by the user and the table below shows the different thresholds for the MODCODs: |
24 | 3 | GAY, Adrien | |
25 | 3 | GAY, Adrien | |
26 | 3 | GAY, Adrien | Table thresholds MODCOD |
27 | 3 | GAY, Adrien | |
28 | 3 | GAY, Adrien | |
29 | 3 | GAY, Adrien | Once the optimal MODCOD has been estimated at the demodulator, this information is sent back to the emitter side. Two options are possible: in-band or out-band signaling. This last one does not send the signaling messages back via the satellite but use another possible links (via a terrestrial network for example); it is not the one chosen for this project. We used in-band signaling, consisting in sending the MODCOD signaling messages directly via the return channel of the satellite link as non routable encapsulated IP packets. |