Edit History

Sidebar »

Preliminary testing » History » Version 6

DE GENDRE, Raphaëlle, 03/23/2016 02:54 PM

1 1 DE GENDRE, Raphaëlle 
h1. Sofware installation
2 1 DE GENDRE, Raphaëlle 





    3
    6
    DE GENDRE, Raphaëlle
    
The first step was to install the software MPLAB X IDE with the compiler XC 16 and to add all the required libraries and files to start coding on the development board. To do so, we used the tutorial by Tony Colin and Brice Duhautois: https://sourceforge.isae.fr/projects/erasure-codes-for-cubesat-missions/wiki/II%20-%20Tutorial%20-%20Simple%20project%20on%20CubeSat%20Kit





    4
    1
    DE GENDRE, Raphaëlle
    





    5
    2
    DE GENDRE, Raphaëlle
    
h1. Erasure code tests





    6
    1
    DE GENDRE, Raphaëlle
    





    7
    1
    DE GENDRE, Raphaëlle
    
In order to get acquainted with the equipment, we tested the code provided by Tony Colin and Brice Duhautois. We downloaded all the necessary files and we put it under a MPLAB X project. We first tested it on the simulator and then we loaded it on the developpement board. We observed the expected results both in the simulator and with the leds on the developpement board.





    8
    2
    DE GENDRE, Raphaëlle
    





    9
    2
    DE GENDRE, Raphaëlle
    
p=. !{width:50%}ErasureCodeTest1.jpg!





    10
    2
    DE GENDRE, Raphaëlle
    
p=. !{width:50%}ErasureCodeTest2.jpg!





    11
    2
    DE GENDRE, Raphaëlle
    
Figure 1: Test with the Erasure Code





    12
    2
    DE GENDRE, Raphaëlle
    





    13
    2
    DE GENDRE, Raphaëlle
    





    14
    1
    DE GENDRE, Raphaëlle
    





    15
    1
    DE GENDRE, Raphaëlle
    
h1. Test with the spectrum analyser





    16
    1
    DE GENDRE, Raphaëlle
    





    17
    5
    DE GENDRE, Raphaëlle
    
We plugged the RF transmitter on the developement board  and we loaded a simple program to send a serie of 1 to the RF input.





    18
    3
    DE GENDRE, Raphaëlle
    





    19
    1
    DE GENDRE, Raphaëlle
    
p=. !{width:50%}Test.jpg!





    20
    5
    DE GENDRE, Raphaëlle
    
Figure 2: First Test with the RF





    21
    1
    DE GENDRE, Raphaëlle
    





    22
    5
    DE GENDRE, Raphaëlle
    
When we used this configuration with the conductive plate, we did not receive any signal on the spectrum analyser. Trying to understand where the problem was, we used a voltmeter to check if the RF transmitted received the voltage it was supposed to have (5V). When we did that, we noticed that the voltage was the right one on the wire connected to the plate, but when we looked at the actual transmitter, it did not receive any voltage. We concluded that there was a problem with the card and we decided to weld little plugs to wires to connect the RF:





    23
    5
    DE GENDRE, Raphaëlle
    





    24
    1
    DE GENDRE, Raphaëlle
    
p=. !{width:50%}SecondSetup.jpg!





    25
    5
    DE GENDRE, Raphaëlle
    
Figure 3: Second set up





    26
    1
    DE GENDRE, Raphaëlle
    





    27
    5
    DE GENDRE, Raphaëlle
    
With this set-up, we started to receive signal on the spectrum analyser.





    28
    5
    DE GENDRE, Raphaëlle
    





    29
    1
    DE GENDRE, Raphaëlle
    
p=. !{width:50%}preliminarytest.jpg!





    30
    5
    DE GENDRE, Raphaëlle
    
Figure 4: Test with the spectrum analyser