Configuration » History » Version 3

Cuadro, Juan Pablo, 11/27/2014 05:21 PM

1 1 Cuadro, Juan Pablo
h1. EL470 Configuration
2 1 Cuadro, Juan Pablo
3 1 Cuadro, Juan Pablo
----
4 3 Cuadro, Juan Pablo
5 3 Cuadro, Juan Pablo
{{toc}}
6 1 Cuadro, Juan Pablo
7 1 Cuadro, Juan Pablo
h2. Equipment wiring
8 1 Cuadro, Juan Pablo
9 1 Cuadro, Juan Pablo
(CREATE DRAWING WITH BLOCKS AND PORTS, INCLUDE VSTs, MODEMS, SWITCH, PCs)
10 1 Cuadro, Juan Pablo
11 1 Cuadro, Juan Pablo
h2. EL470 Configuration
12 1 Cuadro, Juan Pablo
13 1 Cuadro, Juan Pablo
Both HUB and station modems will be configured as layer 2 ethernet bridges. 
14 1 Cuadro, Juan Pablo
15 1 Cuadro, Juan Pablo
h3. HUB Configuration
16 1 Cuadro, Juan Pablo
17 1 Cuadro, Juan Pablo
As an initial step, one can start by using the Setup Wizard configuration option on the management interface (accessed by a web browser on the management IP of the HUB modem). In this wizard we can input the following options:
18 1 Cuadro, Juan Pablo
19 1 Cuadro, Juan Pablo
* Network Topology: Point-to-Point
20 1 Cuadro, Juan Pablo
* Bridge Type: L2 Ethernet Bridge
21 1 Cuadro, Juan Pablo
* Interface and Encapsulation Settings:
22 1 Cuadro, Juan Pablo
** Ethernet Port: A (needs to be consistent with wiring)
23 1 Cuadro, Juan Pablo
** Encapsulation: XPE
24 1 Cuadro, Juan Pablo
** CRC: Disabled
25 1 Cuadro, Juan Pablo
* Modulation Settings:
26 1 Cuadro, Juan Pablo
** Output Frequency: 1750 MHz
27 1 Cuadro, Juan Pablo
** Symbol Rate: 256 KBaud
28 1 Cuadro, Juan Pablo
** Roll Off Factor: 20%
29 1 Cuadro, Juan Pablo
** Output Level: -35.0 dBm
30 1 Cuadro, Juan Pablo
** FEC Frame Type: Normal
31 1 Cuadro, Juan Pablo
** ModCod: QPSK - 1/4
32 1 Cuadro, Juan Pablo
** Pilots Insertion: Disabled
33 1 Cuadro, Juan Pablo
* Demodulation Settings:
34 1 Cuadro, Juan Pablo
** Demod input: IFL 1 in
35 1 Cuadro, Juan Pablo
** Input Frequency: 1500 MHHz
36 1 Cuadro, Juan Pablo
** Symbol Rate: 256 KBaud
37 1 Cuadro, Juan Pablo
** Roll Off Factor: 20%
38 1 Cuadro, Juan Pablo
39 1 Cuadro, Juan Pablo
After this initial setup, the *Overview* tab in the management interface looks like this:
40 1 Cuadro, Juan Pablo
41 1 Cuadro, Juan Pablo
!{width: 80%}HUB-AfterWizard.png!
42 1 Cuadro, Juan Pablo
43 1 Cuadro, Juan Pablo
Notice that first of all, the modem is not transmitting (Modulator.TX = Disabled). Secondly, the demodulator is configured in ACM mode, we will take care of this by using the Tree tab and defining more specific options relating to the modulation and demodulation schemes. Note that the following only the stated options are to be changed, the rest must remain with their default values which result from the setup wizard.
44 1 Cuadro, Juan Pablo
45 1 Cuadro, Juan Pablo
h4. General Settings
46 1 Cuadro, Juan Pablo
47 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  *Common* 
48 1 Cuadro, Juan Pablo
## Set  *Processing Mode* is to @Eth(IP)<->Air(S2BBF)@.
49 1 Cuadro, Juan Pablo
50 1 Cuadro, Juan Pablo
h4. Modulator Settings:
51 1 Cuadro, Juan Pablo
52 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  Modulation >> *Main*
53 1 Cuadro, Juan Pablo
## Set *DVB-S2 Mode* to @ACM@.
54 1 Cuadro, Juan Pablo
## Set *L-Band Transmit* to @Enabled@ (This will enable the modulator output signal). 
55 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  Modulation >> *ACM Control*
56 1 Cuadro, Juan Pablo
## Set *ACM Ctrl* to @Enabled@.
57 1 Cuadro, Juan Pablo
## Set *MIN Modcod* to the minimum MODCOD parameter desired in the forward link.
58 1 Cuadro, Juan Pablo
## Set *MAX Modcod* to the maximum MODCOD parameter desired in the forward link.
59 1 Cuadro, Juan Pablo
## Set *Comm Failure Modcod* to the default MODCOD parameter utilized if no ACM signalling is able to take place.
60 1 Cuadro, Juan Pablo
## Set *Min Margin*, *Tgt margin*, *Distortion*. For an explanation of FlexACM refer to [[FlexACM Functionality]].
61 1 Cuadro, Juan Pablo
## Set *MODCOD selection algo.* to @Link margin@.
62 1 Cuadro, Juan Pablo
## Set *ACM FW Sig Plane* to @Inband RF@.
63 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  Modulation >> ACM Control >> *Demod table*
64 1 Cuadro, Juan Pablo
## Set the Demodulator IP of the first entry with the *Virtual ACM client id* IP address to be specified later on in the station parameters (we will be using 10.0.0.254).
65 1 Cuadro, Juan Pablo
66 1 Cuadro, Juan Pablo
!{width: 80%}HUB-TreeOptions.png!
67 1 Cuadro, Juan Pablo
68 1 Cuadro, Juan Pablo
h4. Demodulator Settings:
69 1 Cuadro, Juan Pablo
70 1 Cuadro, Juan Pablo
Return link will always be CCM and we will use QPSK-1/4 with short FEC-Frame types.
71 1 Cuadro, Juan Pablo
72 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >> Demodulation
73 1 Cuadro, Juan Pablo
## Set *DVB-S2 Mode* to @CCM@.
74 1 Cuadro, Juan Pablo
## Set *FEC-Rate and Mod* to @QPSK-1/4@
75 1 Cuadro, Juan Pablo
## Set *FEC-Frame Type* to @Short@
76 1 Cuadro, Juan Pablo
77 1 Cuadro, Juan Pablo
h3. Station Configuration
78 1 Cuadro, Juan Pablo
79 1 Cuadro, Juan Pablo
* Network Topology: Point-to-Point
80 1 Cuadro, Juan Pablo
* Bridge Type: L2 Ethernet Bridge
81 1 Cuadro, Juan Pablo
* Interface and Encapsulation Settings:
82 1 Cuadro, Juan Pablo
** Ethernet Port: A (needs to be consistent with wiring)
83 1 Cuadro, Juan Pablo
** Encapsulation: XPE
84 1 Cuadro, Juan Pablo
** CRC: Disabled
85 1 Cuadro, Juan Pablo
* Modulation Settings:
86 1 Cuadro, Juan Pablo
** Output Frequency: 1500 MHz
87 1 Cuadro, Juan Pablo
** Symbol Rate: 256 KBaud
88 1 Cuadro, Juan Pablo
** Roll Off Factor: 20%
89 1 Cuadro, Juan Pablo
** Output Level: -35.0 dBm
90 1 Cuadro, Juan Pablo
** FEC Frame Type: Normal
91 1 Cuadro, Juan Pablo
** ModCod: QPSK - 1/4
92 1 Cuadro, Juan Pablo
** Pilots Insertion: Disabled
93 1 Cuadro, Juan Pablo
* Demodulation Settings:
94 1 Cuadro, Juan Pablo
** Demod input: IFL 1 in
95 1 Cuadro, Juan Pablo
** Input Frequency: 1750 MHHz
96 1 Cuadro, Juan Pablo
** Symbol Rate: 256 KBaud
97 1 Cuadro, Juan Pablo
** Roll Off Factor: 20%
98 1 Cuadro, Juan Pablo
99 1 Cuadro, Juan Pablo
Management interface after setup wizard:
100 1 Cuadro, Juan Pablo
101 1 Cuadro, Juan Pablo
!{width: 80%}Station-AfterWizard.png!
102 1 Cuadro, Juan Pablo
103 1 Cuadro, Juan Pablo
As with the HUB, we must further define some other options:
104 1 Cuadro, Juan Pablo
105 1 Cuadro, Juan Pablo
h4. General Settings
106 1 Cuadro, Juan Pablo
107 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  *Common* 
108 1 Cuadro, Juan Pablo
## Set  *Processing Mode* is to @Eth(IP)<->Air(S2BBF)@.
109 1 Cuadro, Juan Pablo
110 1 Cuadro, Juan Pablo
111 1 Cuadro, Juan Pablo
h4. Modulator Settings:
112 1 Cuadro, Juan Pablo
113 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  Modulation >> *Main*
114 1 Cuadro, Juan Pablo
## Set *DVB-S2 Mode* to @CCM@.
115 1 Cuadro, Juan Pablo
## Set *L-Band Transmit* to @Enabled@ (This will enable the modulator output signal). 
116 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >>  Modulation >> DVB-S2 Streams >> *DVB-S2 Streams*
117 1 Cuadro, Juan Pablo
## Enable (*Active* field) the first stream entry and set *FEC-Rate and Mod.* and *FEC-Frame Type* according with whatever settings the HUB demodulator is using.
118 1 Cuadro, Juan Pablo
119 1 Cuadro, Juan Pablo
h4. Demodulator Settings:
120 1 Cuadro, Juan Pablo
121 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >> *Demodulation*
122 1 Cuadro, Juan Pablo
## Set *DVB-S2 Mode* to @ACM@.
123 1 Cuadro, Juan Pablo
## Set *Max Achievable ModCod* to preferred value.
124 1 Cuadro, Juan Pablo
# Go to Tree >> EL470 >> Modem >> Control >> Demodulation >> *ACM Client*
125 1 Cuadro, Juan Pablo
## Set *Virtual ACM Client ID* to @10.0.0.254@.
126 1 Cuadro, Juan Pablo
## Set *ACM RT Sig Plane* to @Inband RF@.
127 1 Cuadro, Juan Pablo
## Set *MODCOD Selection Algo.* to @Link Margin@
128 1 Cuadro, Juan Pablo
## Set *Delta Margin* and *Fade Prediction* fields accordingly. For an explanation of FlexACM refer to [[FlexACM Functionality]].
129 1 Cuadro, Juan Pablo
130 1 Cuadro, Juan Pablo
!{width: 80%}Station-TreeOptions.png!
131 1 Cuadro, Juan Pablo
132 1 Cuadro, Juan Pablo
h2. Good Link Example
133 1 Cuadro, Juan Pablo
134 1 Cuadro, Juan Pablo
In the following screenshots we can see the management interface when a link has been established. Es/N0 estimates are of around 30dB and FW link is ACM while RT link is CCM with short QPSK - 1/2 FEC-frames.
135 1 Cuadro, Juan Pablo
136 1 Cuadro, Juan Pablo
137 1 Cuadro, Juan Pablo
Station:
138 1 Cuadro, Juan Pablo
!{width: 80%}Station-LinkGood.png!
139 1 Cuadro, Juan Pablo
140 1 Cuadro, Juan Pablo
141 1 Cuadro, Juan Pablo
HUB:
142 1 Cuadro, Juan Pablo
 !{width: 80%}HUB-LinkGood.png!